Flexnet Licensing Programming And Reference Guide

1. Flexnet Licensing Programming And Reference Guide Download
2. Flexnet Licensing Programming And Reference Guide Manual
3. Flexnet Licensing Programming And Reference Guide 2020
4. Flexnet Licensing Programming And Reference Guide Pdf
5. Flexnet Licensing Programming And Reference Guide 2020

The program that runs the FlexNet License Server service is flexnetlsw.exe, located in the INSTALL-DIR flexnetls-x64windows-xxxx.xx.x server directory. If needed, consult your local system or network administrator for assistance in configuring your server's firewall. Follow the steps below to install, authorize, and start the license manager: Run the License Manager setup from your My Esri software download or from the ArcGIS installation media. Follow the instructions to install the license manager and FlexNet licensing service. At the end of the installation, ArcGIS License Server Administrator appears. Next go to the folder where the Activation Wizard program files are located (syntax below) cd C: Program Files (x86) Common Files FotoWare Application Activation Wizard 1.1 Now, type the following command to install the FlexNet service. Fwappactwiz -installService. Finally, close the command prompt: exit. Compliance and Regulatory Enforcement (CARE) Tools. As part of the Inspection Process Project (IPP), the Community Care Licensing Division (CCLD) has developed the CARE Tools for use in the Adult and Senior Care Program, Children's Residential Program, and Child Care Program.

How to Use This Manual. Licensing v and FLEXlm versions through The FLEXnet Licensing Programming and Reference Guide is for. The Software was developed fully at private expense. All other use is prohibited. Book Name: FlexNet Publisher R3 () License Administration Guide. This manual explains FLEXlm for administrators and end users and describes The FLEXlm Programmers Guide and FLEXlm Reference Manual are for.

However, if all licenses are stored and managed in a single license server, failure of that server can result in a failure of the entire license management system.

If an insufficient number of allocations are available to completely satisfy the request, no authorizations are sent, and follower server B communicates another message back to the client computer 12denying the request. A system for managing licenses for protected software on a communication network is disclosed.

Modern software programs can require months or even years of development, often involving expensive resources and teams of highly skilled engineers and programmers, before a product may be readied for sale or gude.

FAQ I see an error message when running Origin installshield. The preceding discussion described a client computer 12 requesting prorammers receiving authorization for running a protected software program from a networked license server This initial distribution lfexlm also signifies that the pool will comprise three license servers. Year of fee payment: For example but not illustrated in FIG. The network administrator then runs a utility 62 on any of the license servers 14 in the server pool that effectively sends a request for a commuter authorization to the targeted license server The network administrator is then provided encrypted commuter authorization information as described above.

An example hardware environment for an embodiment of the present invention is illustrated, generally, in FIG. In contrast, pinging is disabled when a client computer 12 receives a commuter authorization from a license server The system includes at least one client computer that is capable of being coupled to or decoupled from the communication network.

Documentation

How do I do this? A system as recited ugide claim 1wherein while the requesting client computer maintains a valid commuter authorization, the requesting client computer may open the protected software multiple times, including simultaneous instantiations of the protected software. A method as recited in claim 10the step of granting a commuter authorization to the at least one client computer from the at least one license server further including the steps of: Save as PDF Email page.

All concurrent licenses are in use The License Information dialog will provide a message stating that all licenses are in use. FAQ I have registered Origin. Note also that in the embodiment of FIG. It should be noted, however, that although embodiments of the present invention described herein prograkmers a pool or license servers 14in alternative embodiments only a single license server 14 is required for issuing commuter authorizations.

How do I fix this problem? This updated version includes a security update from flexera which fixes vulnerability CVE The client computer may then use the protected software while coupled to or decoupled from the communication proggammers until the commuter authorization lifetime expires. This download contains utilities that must be installed by your System or License Administrator if your company is using Wind River products that require license management and you have purchased floating or Named User licenses.

Description of Related Art The increasing popularity of computer usage in homes and businesses, as well as in governmental, research and education institutions, has brought about a world-wide demand for greater software variety fkexlm sophistication.

What are the Issues?

Flexlm Licenses manager – Siemens PLM Community –

Programmfrs do I get my Product Key? In preferred embodiments of the present invention, each RLF 24 stored in each license server 14 is an exact copy of every other RLF 24 of license servers in the pool.

Method for multiple programs management within a network having a server computer and a plurality of remote computers. Instead, only one license management program needs to be running on a given license server 14to manage licenses for protected vendor applications managed by that license server.

How to use citra emulator on mac. Selection of a leader server is described in a related U. It is a further advantage of embodiments of the present invention to provide a system and method for managing licenses on a network that allows a client computer to request and receive a commuter authorization from a license server while connected to the network, allowing the client computer to run a protected software program even if the client computer should become disconnected from the network.

While coupled to the communication network, a user of the client computer may request a commuter authorization to use the protected software. How to activate my free upgrade to the new version? How do I fix this problem?

FLEXlm End User Manual

The down server computer would not respond guude the poll, but other server computers having appropriate license information in their license file would respond to the poll, thus, allowing the client computer to continue to seek authorization to run the protected software program, even though one of the servers was down. I am the Admin on this computer – so what do I do?

The license server stores and manages software licenses for the network users, in accordance with a license management program stored on the server. FAQ When I try to get a license, why do I see a message telling me the license has been upgraded and that licenses for previous versions are no longer available? In preferred embodiments of the present invention, a user may then return the commuter authorization to the network by running a utility 54 that invokes the client library 52 associated with the requested software program 50 and selecting a check-in function.

If authorization is permitted, then an instantiation of the protected software program 50 is opened. Method and apparatus for assigning consequential rights to documents and documents having such rights.

FAQ I try to start Origin but nothing happens! Film my heart indonesian full movie. If so, the server flexln an authorization message to the user and decrements a count of available licenses fflexlm by the server. For example, prior to leaving for a business trip or working at home, a user can request a commuter authorization for one or more protected applications from a client computer 12 connected to the network.

Wind River License Administration Tools 1. It is to be understood that other embodiments may be utilized and structural changes may be made without departing from the scope of the preferred embodiments of the present invention. Furthermore, within the license server 14the number of available allocations is incremented by one, and this change communicated to the leader server. Thus, attributes of the license code 26 such as the expiration date or number of allocations need not be passed between license servers 14 in response to a request for authorization to used a protected software program from a client computer 12because an exact copy of the license code 26 has already been stored on the hard disk of each license server 14 prior to the startup of that license server If yes, then you should apply an Origin patch to resolve the problem.

Once received, the client computer 12 can be disconnected from the network, because the commuter authorization information received by the client library 52 allows it to independently perform a function similar to a license server

Open Inventor is protected by a license key mechanism limiting its usage to specified computers or network environments based on commercial agreements. In this chapter, we explain how to setup the licensing for the different licensing cases.

Note: temporary licenses can be sent for evaluation purpose. These licenses are not locked to a specific computer but are time limited. Please go to the trial version request page for getting a trial license.

• Setting up a floating license environment

Licensing overview

Your license(s) of Open Inventor and associated extensions have been designed to run on a specific hardware configuration and used by a specified number of users. You might have purchased either node-locked licenses, which are individually bound to identified equipment, or a floating license, which is to be installed on a specified number of single computers driven by a license server.

Each type of license requires a specific License Key (so called password) to be activated. In order to get this password, we need you to provide us with the hostID of your computer for node-locked licenses, or the hostID and hostname of your license server for floating licenses.

The Open Inventor licensing mechanism uses the FLEXnet technology, by Flexera.

Note: the hostID was called the ComputerID in versions of Open Inventor prior to 8.6.

Setting up a node-locked license

Node-locked licenses are licenses which allow you to use Open Inventor on an identified computer. Designated equipment(s) are identified by a hostID.

Getting the hostID

To activate your node-locked license, we need the hostID of your computer.

1. 1. Open a command console on Windows or a command shell on a Linux platform
   2. Disable all temporary network connections (wlan card, bluetooth, docking station, …)
   3. Go to the directory (depending on the language binding and platform installed):
      /license/
      or
      /arch--release/license/
      (where is the platform architecture for instance Linux-x86_64-gcc41)
   4. To get the hostID, execute the command ‘lmhostid'

Note: The ComputerID displayed in the Open Inventor V8.x License Manager (Ladmin) does not match the FlexNet hostID. Do not use this value as hostID. The Ladmin tool is now deprecated.

Requesting your license key

Once you have the hostID, go to our online password delivery center and fill in your details, Open Inventor and extensions license numbers, along with your hostID.

Installing the license key

You will receive the license keys by email as well as the installation instructions. The provided license file must be copied in the /License/password.dat or /arch*release/license/password.dat directory in order to unlock the product.

Where OIVHome is the installation path of the Open Inventor package.

Setting up a floating license environment

Overview

Read this section only if you have purchased a floating license for your site where a single license server provides the license key for several users located on other machines of the same network environment. Standalone licenses also called nodelock licenses, application password licenses and temporary licenses are not managed using this mechanism.

Open InNventor uses the FLEXnet licensing option to support floating licenses. In this scenario, a site purchases a specific number, N, of Open Inventor licenses. The FLEXnet license server tracks the licenses being used and allows simultaneous use of up to N instances of the Open Inventor software. The advantage of this approach is that, unlike standard Open Inventor licensing, Open Inventor is not locked to a specific computer, but can be run on any computer that can communicate with the license server.

A small set of FLEXnet-related files are provided for managing the FLEXnet licensing. These files must be copied onto the system to where the license server will be run. The license server can be run on the same system where Open Inventor is installed, but it doesn't have to be.

One of the supplied files, lmgrd ('license manager daemon'), is a FLEXnet executable that is responsible for starting the vendor daemon, which does the actual checking in and out of licenses specific to that vendor. The supplied vendor daemon, mcslmd ('license manager daemon'), handles the requests for licenses from the Open Inventor application programs.

There is a FLEXnet license file that is read by the server. This license file contains information indicating which products are licensed and how many licenses are allowed for each.

In addition, each Open Inventor installation has a separate license file which indicates the name of the FLEXnet license server.

The sections below will provide the basic technical details of installing and managing a FLEXnet license server.

For complete technical details regarding FLEXnet itself, see the Web site of Flexera Software, supplier of the FLEXnet licensing software (www.flexerasoftware.com):

Getting Started

The first thing to do is decide on which computer you wish to run the FLEXnet license server. This system should be 'visible' from any system that might want to request a license. It should also be highly reliable.

The server can be installed on a computer on which Open Inventor is installed, but it does not have to be.

It is possible to do FLEXnet licensing in a heterogeneous environment. That is, the server and Open Inventor can be running on different operating systems. For instance, the FLEXnet server could be on a Linux box, with the Open Inventor users running Open Inventor on a Windows platform.

Flexnet Licensing Programming And Reference Guide Download

If your site already has a FLEXnet license server running that is used for licensing other vendors' products, this may affect where and how you decide to configure the Open Inventor license server. The FLEXnet documentation from Acresso can help you with this decision. See, for example, the chapter 'Managing Licenses from Multiple Vendors' in the FLEXnet Licensing End User Guide.

For the rest of this discussion, we will assume that you will be setting up a license server used only for licensing Open Inventor.

Once you have selected the server machine, if you are not going to run the server from the Open Inventor installation directory (i.e., from //license), you will need to copy the FLEXnet-related files we've provided to that system into an empty directory.

Suggested server directory name:

The FLEXnet files are provided in:

On the Open Inventor download pages, FLEXnet files are also available for platforms other than the one on which you will be running Open Inventor.

Open Inventor 9.9.x requires FLEXnet tools 11.14.0.0.
Open Inventor 10.x to 10.1.x requires FLEXnet tools 11.16.0.0.
Open Inventor 10.2.x and above requires FLEXnet tools 11.16.0.0.

Instructions for installing and configuring the server are provided in below.

Getting the hostID and host name

In order to generate a FLEXnet license, we will need the following information about the system on which the license server is running/will run:

1. its host name (or IP address), and
2. its host ID.

• Linux
  1. On the system where the server is running/will run, in a command shell, go to the directory where the server will be installed:
  2. To get the host ID, execute the lmutil program as follows:

     The output will look like:

  1. To get the hostname, you can use any of the following commands:
  2. To get the IP address (optional):
  3. Save the lmhostid output and the hostname (or IP address).
• Windows
  1. On the system where the server is running/will run, run LMTOOLS. It should be located in:
  2. Click on the Systems Settings tab.
  • The Computer/Hostname field contains the required host name.
  • The Ethernet Address field contains the required host id.
  • The IP Address field contains the optional IP address.
  1. Save those values

Requesting your license key

Once you have the hostID and host name, go to our online password delivery center and fill in your details, Open Inventor and extensions license numbers, along with your hostID and host name.

Installing the FLEXnet Server (Linux)

At this point, we assume that the FLEXnet files are in their desired location:

• either in the default location, //license
• or have been copied to /oiv_flexnet directory on the system where the server will run.

The vendor daemon mcslmd must be in the same directory as lmgrd.

The command to start the server looks like:

where:

• is the full path to the server license file, and
• is the path to the debug log file.

Prepending the + character the the log file name causes log entries to be appended.

The following is the suggested command to use:

TIP: It can be convenient to set up the server so that it is started automatically upon system reboot. This would involve editing the system boot script. See the FLEXnet Licensing End User Guide, chapter 'The License Server Manager' for details.

Installing the FLEXnet Server (Windows)

At this point, we assume that the FLEXnet files are in their desired location:

• either in the default location, license
• or have been copied to oiv_flexnet directory on the system where the server will run.

FLEXnet uses a program called lmgrd to manage licenses. On Windows, FLEXnet provides a GUI called LMTOOLS that allows one to configure lmgrd to run as a service. This is the preferred method of configuring FLEXnet and is outlined below.

NOTE: To configure a license server as a service, you must have Administrator privileges.

The vendor daemon mcslmd.exe must be in the same directory as lmgrd.exe.

Starting the Server (Windows)

Installing the Server License File

• Linux
  On Linux, the server license file is specified when the server is started.
  1. Decide where you want to place the server license.Recommended location:
  2. Using a text editor, copy the server license strings into that file.

  Start the server:

• Windows
  1. Decide where you want to place the server license file.Recommended location:
  2. Using a text editor, copy the server license strings into that file.
  3. Run LMTOOLS, click on the Config Services tab, then specify the 'path to the license file'.
  4. For this change to take effect, stop and restart the server using the Start/Stop/Reread tab.

Installing the Client License Files (All Platforms)

Each system that might request an Open Inventor license from the FLEXnet license server must have an Open Inventor license file.

Here's an example client license file:

On each client system, copy the client license info to the Open Inventor license file.

The default (and recommmended) location is:

This can be changed by setting the VSG_LICENSE_FILE environment variable to a new path, including the file name. Once this variable is set, Open Inventor automatically looks for the license file in the specified location. If Open Inventor cannot find the license file, the user is presented with a dialog that asks for the license information.

Nomad Licensing / Borrowing

To use a FLEXnet floating license on a system that is not always connected to the license server, you will need to 'borrow' a license while you are connected to the server, then disconnect from the server. This kind of licensing is what we call 'nomad' licensing. Below are the detailed instructions. We will assume that standard FLEXnet licensing, i.e., not borrowing, is already working correctly.

• Linux
  1. On the client machine, in a command shell, go to the directory where the FLEXnet utilities are installed. By default, these utilities are found on the client machine in: //license.cd //license
  2. To initiate borrowing, execute the lmutil program on the client as follows:lmutil lmborrow mcslmd where: Enddate is the date the license is to be returned in dd-mmm-yyyy format. Time is optional and is specified in 24-hour format (hh:mm) in the FLEXenabled application local time. If time is unspecified, the checkout lasts until the end of the given end date.For example:lmutil lmborrow mcslmd 16-jan-2007 13:00

  To print information about borrowed features, issue the following command on the machine from which they are borrowed:

  lmutil lmborrow -status

• Windows
  1. Run LMTOOLS on the client machine. By default, LMTOOLS is found on the client machine in: //license.
  2. Click on the Borrowing tab.
  3. Specify a return date.
  4. Optional, specify the vendor name (mcslmd).
  5. Press the Set Borrow Expiration button.
  6. Start your Open Inventor Application, then use all of the extensions that you want to borrow.
  7. Disconnect from the network.
  8. Exit your Open Inventor Application and confirm that you can restart it and use all of the borrowed modules.

You can check how many licenses are checked-in or out by pressing the List Currently Borrowed Features button of the Borrowing tab of the LMTOOLS application.

Additional controls can be set directly into the license string. The most important are:

• Limit the number of token that can be borrowed:
  Examples: The customer want to keep 60 tokens over his 100 tokens, so only 40 tokens can be borrowed.
  Add a BORROW_LOWWATER line:

Flexnet Licensing Programming And Reference Guide Manual

• Limit the number of days a token can be borrowed:
  Examples: One week (7days x 24hours = 168hours). Add a MAX_BORROW_HOURS line:
  MAX_BORROW_HOURS Product 168
  Notes: If not specified, default value is one year.
• Specify who is allowed to borrow:
  • a user
    INCLUDE_BORROW Product USER Jim
  • a group of users
    INCLUDE_BORROW Product GROUP project_dev
  • a computer
    INCLUDE_BORROW Product HOST hots_name
  • a group of computers
    INCLUDE_BORROW Product HOST_GROUP computer_group
• Specify who is not allowed to borrow:
  • a user
    EXCLUDE_BORROW Product USER Jim
  • a group of users
    EXCLUDE_BORROW Product GROUP project_dev
  • a computer
    EXCLUDE_BORROW Product HOST hots_name
  • a group of computers
    EXCLUDE_BORROW Product HOST_GROUP computer_group

Defining groups

• Group of users:
  GROUP project_dev Jim Mike Bob
• Group of computers:
  HOST_GROUP computer_group host1 host2 host3

Reserving tokens

Tokens can be reserved for specific users groups or computers.

• Reserve 10 tokens for an user:
  RESERVE 10 Product USER Jim
• Reserve 10 tokens for a group of users:
  RESERVE 10 Product GROUP project_dev
• Reserve 10 tokens for a computer:
  RESERVE 10 Product HOST host1
• Reserve 10 tokens for a group of computers:
  RESERVE 10 Product HOST_GROUP computer_group

Setting Access Permissions

Flexnet Licensing Programming And Reference Guide 2020

You can control who is allowed to use a product using the INCLUDE EXCLUDE commands.

• Who is allowed to use a product :
  INCLUDE Product USER Jim
  Can be used for GROUP, HOST and HOST_GROUP as described above.
• Who is not allowed to use a product :
  EXCLUDE Product USER Mike

Troubleshooting

Flexnet Licensing Programming And Reference Guide Pdf

Refer to the FLEXnet documentation. The FLEXnet Licensing End User Guide contains a troubleshooting appendix.

Flexnet Licensing Programming And Reference Guide 2020

Finally if you need assistance getting your FLEXnet licenses installed and operational, please contact the technical support.